Ways to Dry Out Walls After Water Damage

Following an event that leads to water damage in your home, not only would the floors be affected, but often the walls are also. Therefore, it’s essential to know how to wash wet walls–or call a restoration firm immediately. Fast drying reduces the danger of structural damage and prevents mold from growing. 

Understanding How Water Saturates Drywall

Before you understand how to dry a wall after water damage, here is a look into how water flows drywall. Water which enters a space from floor level will pay for the ground and floor covering. It is going to then start to”wick” up the walls due to capillary action in porous materials. The extent of the movement depends upon the wall’s construction, the amount of water, along the water’s height on the wall substance.

Drywall is an absorbent material that includes gypsum plus a cardboard-like newspaper on either side. The water will be present on each side of the wall. Often, however, it is higher on the inside as a result of restricted evaporation on that side of the drywall. While water damage is occasionally visible, at other times, the wall doesn’t show indications of moisture.

The Way to Wash a Wall After Water Damage

We recommend the latter if you don’t know how to wash wet walls or so the damage is more extensive. From time to time, the water damage is clear, but most times, it is hidden, and those not trained in water damage restoration could miss it.

If you would like to DIY, here is how to dry wet walls out:

If a burst pipe resulted in the water intrusion, then switch off the water resource. Hire a plumber to repair the broken pipe before any drying can occur.

Accelerate drying by opening doors and windows. Use fans to move air around the moist walls. Dehumidifiers can help remove moisture from the atmosphere, which indirectly removes it from the walls, also.

To speed up evaporation, eliminate molding and baseboards to prevent moisture from entering behind them. Store the molding in a dry, secure place to prevent damaging it. Also, remove objects hanging on the walls, such as paintings and portraits.

Eliminate wallpaper if you’ve got it. This requires patience, but it is important as the background creates a”seal” that holds moisture in the wall. Wallpaper removal options, which split the glue, and are available in the hardware store. You will also need 3″-6″ broad knives to scratch on the wallpaper once released.

Note that fully drying walls out takes some time, so don’t rush the refinishing until the walls are dry. A moisture meter will help you be sure. Once fully dry, you can reverse the process and refinish your room. Inspect the eliminated items for almost any moisture or mold growth before reinstalling.

Drying wet walls quickly and correctly is vital. If you can not dry your walls instantly, do not let the problem get worse. Telephone a water damage remediation specialist and leverage their expertise, experience, and equipment.

How restoration professionals warm damp walls after water damage

First, technicians determine the degree of the water by means of a range of water damage restoration tools. This meter uses radio waves to test for water without putting holes in the wall.

Considering that the evaporation from wet walls makes them cooler than dry walls, the IR camera can find water in walls.

After the professionals identify wet walls, they use specialized drying equipment to dry them.

When the walls are not insulated:

In this case, the restoration specialist may dry wet walls out without holes or removing the baseboard. The technicians place high capacity air movers along the wall every 10 to 14 feet. As the moisture evaporates, more moisture extends to the surface where it evaporates.

The restoration specialist will also put in a very low grain refrigerant dehumidifier in the moist wall. This innovative drying equipment reduces the humidity levels to aid with drying and prevent mold growth. Learn more about mold removal right here.

When proper, the restoration professional will set up an inner-wall drying system by putting small holes over the sill plate and then forcing air into the wall cavity. Studies have shown that this solution is the very best and fastest way to wash walls with water damage.

Additionally, if there’s a moisture barrier on the outside or within the wall, the drying strategy changes. Moisture obstacles are coatings or substances that inhibit the movement of moisture from the wall material.

Most latex paints are permeable and don’t make a barrier. But, glossy paints can create a barrier and enamel paint or vinyl wall coverings make a complete barrier. Technicians need to perforate or remove them allowing moisture to escape and also the walls to dry. If there’s foil or plastic to the inside of the wall, then technicians need to eliminate the wall. That is because drying will not happen properly and mold will grow in such situations.

If the walls are insulated:

When there is fiberglass insulation with paper backing, then an inner-wall drying system may be used, as explained previously. But, if the insulation is foil-backed fiberglass, blown-in cellulose, or a Styrofoam substance, then it can not be dried successfully.

In those instances, eliminating the damaged portion of the wall together with the insulating material is crucial to allow rapid drying and to prevent mold growth.

Tracking the drying procedure

Irrespective of the processes utilized by the restoration professional, homeowners should be aware that the equipment has to function, without stopping, throughout the drying process.

Finally, restoration professionals can monitor the drying system at least one time a day. This ensures the equipment is functioning properly during the drying process. Tracking includes moisture measurements to determine when the materials will dry. Substance dryness is measured against comparable rigid contents in that arrangement. When dryness amounts are equivalent, the drying is finished, and the equipment is removed.

To recap, this is the way to dry out damp walls

  1. After fixing the water source, eliminate paintings and other items from the wall.
  2. Open doors and windows to help speed up the drying procedure.
  3. Use fans to move air across the moist walls. Also use dehumidifiers, which can help remove moisture from the atmosphere and walls.
  4. Professionals use tools like moisture meters, infrared imaging devices, dehumidifiers, and heavy duty fans. This ensures the walls are truly dry before additional repair, painting, or refinishing.

A professional restoration company, for example, PuroClean, understands and utilizes the principles and principles of how to wash moist walls. For efficient drywall water damage repair, phone your regional PuroClean office. Our trained and certified technicians can drywalls and other items quickly and thoroughly, preventing additional damage and mold development. Click here for more information.